Products · High-purity N₂ · H₂

99.999 % nitrogen with far less energy

When consumption is large and purity very high, it doesn't pay to ask the PSA for everything. We produce nitrogen at 99.5 % and remove the remaining oxygen with a little hydrogen, generated on site from water.

99.999 %Residual O₂ < 10 ppm
≈ −40 %Energy versus direct PSA
< −60 °CN₂ dew point

The problem

Every nine costs air

A PSA generator can reach 99.999 %, but at a price: it needs about 6.6 Nm³ of compressed air per Nm³ of nitrogen, versus about 2.9 Nm³ at 99.5 %. For the same flow, compressor and generator are more than twice the size, and so is the electricity bill.

With small flows the difference can be absorbed. With hundreds of Nm³/h around the clock, it is the item that decides whether the project is viable.

Nitrogen purity: what each “nine” costs →


The solution

Produce at 99.5 % and purify

1 · PSA at 99.5 %

Low-cost nitrogen

The generator works where it is most efficient: about 2.9 Nm³ of air per Nm³ of N₂ and a compressor less than half the size.

2 · Hydrogen from water

Just what is needed

An electrolyser produces hydrogen on site: two molecules of H₂ for every molecule of O₂ left in the nitrogen. For 700 Nm³/h at 99.5 %, about 7 Nm³/h of H₂.

3 · Palladium reactor

Oxygen becomes water

On the catalyst, residual oxygen and hydrogen react: 2 H₂ + O₂ → 2 H₂O. No combustion temperature or flame is needed.

4 · Drying

Dry, pure nitrogen

An adsorption dryer removes the water formed. Nitrogen leaves at 99.999 %, with O₂ below 10 ppm and a dew point below −60 °C.


Comparison

The figures, for your flow


The hydrogen

From water, on site

Hydrogen is neither bought nor stored: it is produced on demand by electrolysis of water. The current splits the water molecule: hydrogen leaves at the cathode and oxygen at the anode, and a diaphragm keeps them apart.

The electrolyser uses about 0.9 litres of demineralised water per Nm³ of hydrogen: for the 700 Nm³/h example, around 6 to 9 litres per hour. The by-product oxygen is vented outdoors.

  • Demineralised water: reverse osmosis and final polishing, with conductivity control.
  • No hydrogen storage: it is produced at working pressure and in the quantity the purifier requires.
  • The water-treatment reject is not acidic: it is mains water with concentrated salts.
H₂ O₂ DIAPHRAGM − + CATHODE ANODE H₂O H₂O WATER + ELECTROLYTE H₂ bubbles O₂ bubbles
Electrolysis cell · RAV design

Case study
Electronics manufacturer · feasibility study

700 Nm³/h at 99.999 % for reflow ovens and wave soldering

Starting point
An electronic circuit manufacturer used about 4.3 million Nm³ of liquid nitrogen a year, with peaks of 900 to 1,000 Nm³/h in reflow ovens and wave and selective soldering machines. Seven tanker deliveries a week and two cryogenic tanks.
The proposal
Three 350 Nm³/h PSA generators at 99.5 % (two in service, one standby) with a single variable-speed screw compressor. A 7 Nm³/h hydrogen electrolyser, with a standby unit, and a catalytic purifier for 700 Nm³/h. Pure nitrogen stored in two 10 m³ tanks.
The boosters
The client wanted a large reserve to cover peaks and any contingency. So we proposed a variant with four boosters storing N₂ at 40 bar: about 800 Nm³ of reserve. Without that requirement, the tanks work at 7 bar and the plant uses less energy.
Energy
≈ 0.30 kWh per Nm³ of 99.999 % N₂ without boosters, and ≈ 0.37 kWh/Nm³ with 40-bar storage. A direct 99.999 % PSA for the same flow would have needed a compressor of more than twice the power. These are project figures, with a generator needing 2.4 Nm³ of air per Nm³ at 99.5 % and a variable-speed compressor; the comparison uses more conservative values.
Economics
Electricity cost of ≈ €0.03 per Nm³ versus ≈ €0.08 for liquid nitrogen. Including maintenance, the feasibility study gave a payback of about 3.7 years.
700 Nm³/hN₂ at 99.999 %
7 Nm³/hof H₂ to purify
≈ 0.30 kWhper Nm³ of N₂
≈ 3.7 yearspayback

When it pays

Large consumption, very high purity

  • Flows from about 50 Nm³/h; savings grow with flow and operating hours.
  • Electronics: reflow ovens, wave and selective soldering.
  • Heat treatment and metallurgy, where a trace of hydrogen even helps as a reducing atmosphere.
  • Processes that use liquid nitrogen today for its purity, not its flow.

It is not the answer for small flows or food-grade nitrogen: there a PSA at the right purity is simpler.

Safety

Hydrogen in small quantities and under control

  • Hydrogen is produced on demand and consumed immediately: there are no H₂ tanks.
  • Dosing follows the oxygen measured at the inlet, and an analyser monitors O₂ at the outlet.
  • If purity goes off-spec, the gas does not reach the supply network.
  • Classified zone and ventilation around the electrolyser, and H₂ and O₂ vents ducted outdoors.

Frequently asked questions

What people ask us

Does the nitrogen contain hydrogen?

Dosing is stoichiometric: two parts hydrogen for each part oxygen, adjusted to the measured oxygen. A minimal trace of hydrogen may remain. In electronics soldering and heat treatment this is not a problem, and often an advantage. If your process has a hydrogen limit, we take it into account in the design.

What about argon?

Argon from the air (around 0.9 %) accompanies nitrogen in the PSA. It is an inert gas and does not affect these processes. The 99.999 % specification refers to residual oxygen, which is what matters.

From what flow does it pay?

The purifier makes sense from about 50 Nm³/h, and the savings grow with flow and operating hours. The comparison on this page shows the order of magnitude for your case; we give the exact figure with the study.

What maintenance does it need?

That of a PSA generator, plus the electrolyser (water, electrolyte and cell), the purifier's catalyst and adsorption dryer, and analyser calibration. We plan it all in a single annual plan.

Why don't you publish prices?

Because they depend on flow, purity, storage pressure and what you already have installed. After the study we give you a fixed quotation and the cost of your Nm³.

Do you use a lot of high-purity nitrogen?

Tell us your flow, purity and pressure, and we will compare both solutions with your figures.

WhatsApp