Services · Maintenance

Maintenance of nitrogen and oxygen generators

So your gas never stops. We watch your plant continuously, get ahead of faults and, when a visit is needed, we arrive with the diagnosis done and the spare part in hand. Plants from any manufacturer, throughout Spain.

24/7Monitoring
< 1 hRemote support
24–48 hTechnician on site
SpainCoverage

Three ways to maintain a plant

Wait for the fault, or see it coming?

A PSA generator almost never stops all of a sudden. It warns you first: a filter's differential pressure creeps up, the dew point moves, a cycle takes a few seconds longer. The difference between the three approaches is when you find out.

Corrective

Fix what breaks

“We'll call when it fails.”

It looks cheapest until the day of the fault: an unplanned stop, a technician with no prior diagnosis, a spare part that is not in stock and, often, sieve damage that cannot be undone.

Anticipationlow
Preventive

Service by calendar

“One or two visits a year.”

Filters and consumables are changed on time and faults drop a lot. But between visits the plant runs blind: whatever goes wrong in between is discovered once it has already done damage.

Anticipationmedium
Predictive and proactive

Listen to the plant

“The data warns before purity does.”

We continuously measure the signals that anticipate a fault and act before the gas is affected. The intervention is planned, not improvised, and production never notices.

Anticipationmaximum

Simulation

One fault, three endings

On day 2 the compressed-air dryer stops. It is a real and very common fault. Choose how the plant is maintained and watch what happens to the air dew point and to nitrogen purity over the following month.

Day30

Illustrative simulation based on a real case: a sparkling-wine cellar whose generator dropped to half its flow in the middle of harvest because the dryer had stopped and water had saturated the activated carbon.


What 24/7 means

Always watched, always answered

24/7 does not mean a technician at your door at three in the morning. It means your plant is always monitored, no alarm goes unanswered and, when a visit is needed, we come within the agreed time and know what we are coming for.

24/7

Monitoring

Purity, pressures, dew point, cycles and running hours, logged 24 hours a day, 365 days a year.

< 1 h

Remote support

Every alarm or alert gets a technician's response in under one hour, including weekends and harvest.

24–48 h

Technician on site

If a visit is needed, within 24–48 working hours, with the diagnosis done and the part ready.

1 report

Every intervention

What was found, what was done and what should be done next. The same protocol anywhere in Spain.


Real-time maintenance

The signals that anticipate a fault

Purity is the last thing to move. Other signals change first, and those are the ones we watch:

Filter differential pressure: rises slowly as a cartridge clogs. Changing it on time is cheap; waiting lowers inlet pressure and flow.
Air dew point: if it rises, the dryer is failing and water is heading for the sieve.
Inlet pressure and cycle times: reveal leaks, slow valves and compressors that cannot keep up.
Running hours: tell you when each consumable is due, without waiting for the calendar.

This panel simulates how we see it: a filter starts to clog, an alert is raised with days of margin and the change is scheduled without purity moving. That is what GAS4U does.

N₂ plant · liveNormal operation
N₂ purity
Inlet pressure
Dew point
Filter ΔP
Event log

Maintenance plans

Three levels, depending on what a stop would cost you

We choose the plan with you based on what running out of gas would cost. All of them include the annual purity certification.

Plan

Essential

For plants with moderate consumption or a back-up supply.

  • Full annual on-site inspection
  • E 941 purity certification with signed report
  • Replacement of annual filters and consumables
  • Technical report with recommendations
  • Phone support during business hours
Request the Essential plan
Plan

Professional

For plants that run every day and cannot afford to stop.

  • Everything in the Essential plan
  • Two visits a year
  • Valve inspection and O₂ analyser calibration
  • Wear parts included
  • Priority: technician on site in 24–48 h
  • Remote support during business hours
Request the Professional plan
Plan

Integral 24/7

For critical processes where gas must never run out.

  • Everything in the Professional plan
  • GAS4U monitoring 24 h · 365 days
  • Automatic alarms and predictive alerts
  • Remote support in under 1 h, any day
  • Critical spare parts reserved for your plant
  • Monthly performance and consumption report
Request the Integral plan

On every visit

What we check, from air inlet to gas outlet

Most generator faults start before the generator. That is why we inspect the whole plant, not just the box that produces the gas.

01Compressed air

  • Inlet pressure and stability
  • Condensate drains
  • Network leaks
  • Compressor hours and condition

02Filtration

  • Differential pressure of each stage
  • Particulate, coalescing and activated-carbon cartridges
  • Saturation indicators

03Dryer

  • Actual dew point
  • Refrigeration or desiccant circuit operation
  • Automatic drains

04PSA generator

  • Cycle and equalisation times
  • Valve tightness and response
  • Sieve compaction (CMS or zeolite)
  • Purity and flow against commissioning

05Analyser and controls

  • O₂ analyser calibration
  • Set points, alarms and reject valve
  • PLC records

06Receivers and distribution

  • Pressures and safety valves
  • Points of use
  • Booster and cylinders, with their manufacturer
Process valve block of a PSA nitrogen generator
Process valves. Each tower opens and closes hundreds of times a day. A valve that does not close fully lowers purity without raising any alarm.
Pressure regulator with gauge on a generator air line
Pressures. We compare inlet pressure with the pressure in each tower: an abnormal difference reveals saturated filters or line losses.
Pilot solenoid valves in the control panel of a nitrogen generator
Pilot valves. We check that every PLC signal arrives and that every valve responds.

Continuity plan

Gas that never runs out

Good maintenance reduces breakdowns. A continuity plan decides what happens if, even so, something stops. We design it with your plant and put it in writing.

Redundancy

N+1 or standby connection

A second generator or compressor, or a connection to your existing air network, to keep producing during a breakdown or maintenance.

Gas reserve

Cylinders or tank

A cylinder bundle or buffer tank with automatic changeover: if pressure drops, the reserve takes over without anyone touching anything.

Critical spares on site

Tailored kit

Valves, cartridges and sensor defined for your plant and kept in your store. The most likely fault is fixed the same day.

Remote diagnosis

Before travelling

With access to the PLC or with GAS4U we see the plant from outside: if we need to go, we arrive knowing what is wrong and with the part.

Written protocol

Next to the panel

What to do, who to call and how to switch to the reserve, on a sheet next to the plant. And your team trained to do it.


Any brand

Your plant, whoever made it

We maintain PSA nitrogen and oxygen generators from any manufacturer. If your plant has been left without service, or you are not happy with the one you have, we start with a full diagnosis and tell you frankly what condition it is in.

E 941 certification

Purity, proven every year

In every plan we certify the quality of the nitrogen once a year with a calibrated analyser and issue an independent, digitally signed certificate for your audits.


FAQ

What people ask us about maintenance

What exactly does the 24/7 service include?

Three things: the plant is monitored 24 hours a day, 365 days a year; every alarm or alert gets a remote response in under one hour; and, if a site visit is needed, a technician is on site within 24–48 working hours.

Many incidents are solved remotely, with no travel: a set-point adjustment, a valve that needs forcing or an alarm that needs interpreting. Those that are not arrive at the visit already diagnosed and with the spare part ready.

Do you maintain plants from other manufacturers?

Yes. We maintain PSA nitrogen and oxygen generators from any manufacturer. The physics is the same; what changes are the controls and the spare parts, which we source for each brand.

On the first visit we carry out a full diagnosis of the plant and tell you frankly what condition it is in.

Do I need GAS4U for predictive maintenance?

For predictive maintenance, yes: without continuous data nothing can be anticipated. GAS4U connects to the generator PLC or to sensors we add. See how we connect your equipment to GAS4U.

The Essential and Professional plans work without GAS4U, with periodic visits.

What about the compressor, the dryer and the booster?

The compressor and the dryer are part of the plant and we check them on every visit, because they cause most generator faults. The booster is coordinated with its manufacturer or a specialist technician and included in the same plan and the same report.

How often does the carbon molecular sieve (CMS) need replacing?

With properly treated air, CMS lasts many years. We do not replace it by calendar but by performance: on every visit we compare purity and flow with the commissioning values, and warn you when the loss starts to cost money.

Where do you provide service?

Throughout Spain, with the same inspection protocol and the same report on every visit, and with remote support for any connected plant.

Does the service include purity certification?

Yes, in every plan. Every year we certify the quality of the nitrogen at your plant and issue an independent, digitally signed certificate for your IFS, BRC or ISO 22000 audits. Measurements are taken with an oxygen analyser that is calibrated and holds a current calibration certificate, made by a company certified to ISO 9001 and ISO 22000, valid as evidence in IFS Food, BRC and ISO 22000 audits.

When was your plant last inspected?

Tell us which generator you have, how many hours it runs and what is happening. We will propose the plan you need, whoever made your equipment.

WhatsApp