Products · Oxygen

On-site PSA oxygen generators

90 to 95 % oxygen produced at your site from compressed air: no tanks, no trucks and no boil-off losses. Fifteen models that we size for your real consumption.

90–95 %O₂ purity
15Models
141Nm³/h per unit
24 hContinuous production

The principle

A zeolite that attracts nitrogen

An oxygen generator works the other way round from a nitrogen one. Its columns are not filled with carbon sieve but with zeolite: a crystalline aluminosilicate with molecule-sized cavities and metal cations (sodium or lithium) inside.

Those cations create a strong electric field on the cavity surface. The N₂ molecule has a quadrupole moment about four times larger than O₂, and that field holds it much more strongly. At equilibrium, zeolite loads several times more nitrogen than oxygen. It is an equilibrium separation, not a kinetic one.

Lithium zeolites (LiX type) are more selective than conventional 13X and need less air per Nm³ of oxygen. We choose the adsorbent and the cycle according to the flow and purity you need.

N₂
Nitrogen · 78 % of air
Quadrupole moment
high
Zeolite affinity
strong
In the cycle
retained
O₂
Oxygen · 21 % of air
Quadrupole moment
low
Zeolite affinity
weak
In the cycle
product
The 95 % limit: argon (0.9 % of air) is not retained either and leaves with the oxygen. Even if all the N₂ were removed, the product could not exceed 95.7 % O₂.

The PSA cycle

Two columns that take turns

While one column retains nitrogen under pressure and delivers oxygen, the other is depressurised and releases it to atmosphere. The product buffer keeps flow and pressure constant during changeovers.

Diagram of a two-column PSA oxygen generator: column A produces oxygen while column B regenerates COMPRESSED AIR dry and filtered · 7 bar(g) closed COLUMN A ADSORPTION adsorptionfront N₂ retained ZEOLITE COLUMN B REGENERATION ZEOLITE equalisation purge (O₂) BUFFER O₂ O₂ to process vent to atmosphere N₂-enriched air
Column A adsorbing · column B regenerating · PSA = Pressure Swing Adsorption
01 · ADSORPTION

Pressurisation and production

Air enters at 7 bar(g). Zeolite retains nitrogen, moisture and CO₂; oxygen and argon pass through and leave towards the buffer.

02 · EQUALISATION

Recovering pressure

Before the nitrogen front reaches the outlet, both columns are connected. The pressurised one passes oxygen-rich gas to the one about to start.

03 · VENTING

Depressurisation

The saturated column is opened to atmosphere. As pressure falls, the zeolite releases the nitrogen it had retained.

04 · PURGE

Final sweep

A fraction of the product oxygen sweeps the column counter-current and carries the residual nitrogen away. The column is ready to produce.


Purity and consumption

Oxygen is one fifth of the air

To obtain one Nm³ of oxygen, almost four of nitrogen have to be retained, and part of the oxygen is lost in venting and purge. That is why an O₂ generator needs between 10 and 12 Nm³ of compressed air per Nm³ of product, several times more than a nitrogen generator.

An example: 20 Nm³/h of O₂ at 93 % needs about 220 Nm³/h of air, close to 3.7 m³/min. Compressor efficiency drives much of the cost of your oxygen.

For most industrial uses — aquaculture, wastewater, ozone, combustion — 90–93 % is enough.

0 2 4 6 8 10 12 10 90 11 93 12 95 O₂ purity →

Nm³ of compressed air at 7 bar(g) per Nm³ of O₂ produced. The balance of the product up to 100 % is argon and nitrogen.


The range

Fifteen models, from 0.6 to 141 Nm³/h

Each model is named after its flow at 93 %. Choose the purity to see the flow of every model and the compressed air it uses, or try the “Which model do I need?” tab.

Choose the O₂ purity
Purity
Balance N₂ + Ar
Air pressure
Air / O₂
ModelFlowCompressed air
Nm³/h
Connections
air / O₂

Flows in Nm³/h with inlet air at 7 bar(g), 20 °C, dry and oil-free. With other inlet conditions the flow changes: we calculate it for your installation. “Compressed air” is the generator consumption at full output. For larger flows we design units in parallel.


Inlet air

Zeolite does not forgive moisture

Zeolite is strongly hydrophilic: water adsorbs on it even more strongly than nitrogen. If the air arrives wet, vapour takes the active sites, the zeolite loses capacity and purity falls. That is why the air must arrive dry, filtered and oil-free, and many columns carry a layer of activated alumina at the bottom to hold residual moisture.

As with nitrogen, the air receiver, pressure stability and inlet temperature are part of the generator's performance.

Oxygen and safety. In an oxygen-enriched atmosphere, materials that barely burn in air burn violently. Pipes, valves and seals in contact with O₂ must be oxygen-compatible and free of grease and oil, and venting and room ventilation are designed from the start. We take this into account in every installation.
The complete plant
01

Compressor

The largest consumer in the plant: air/O₂ factor of 10 to 12.

02

Dryer

Dry air to protect the zeolite.

03

Filtration

Particulate, coalescing and activated carbon.

04

Air receiver

Stable inlet pressure.

05

PSA generator

Two zeolite columns and cycle control.

06

O₂ buffer

Constant flow and pressure to the process.

07

Analyser

Continuous O₂ purity with alarm.


Applications

Where PSA oxygen is used

Aquaculture

90–95 % O₂

Oxygenation of tanks and pens: more biomass per m³ and less stressed fish in summer.

Wastewater treatment

90–93 % O₂

Oxygenation of biological basins to absorb load peaks and reduce odours without enlarging the plant.

Ozone generation

90–95 % O₂

Feeding the ozone generator with oxygen instead of air multiplies the ozone produced per kWh.

The plant for ozone →

Combustion and furnaces

90–93 % O₂

Enriching combustion raises flame temperature, reduces flue-gas volume and saves fuel.

Glass and jewellery

90–93 % O₂

Oxy-fuel torches for glass blowing, lampworking and goldsmithing, with no cylinder changes.

Oxy-cutting and welding

93–95 % O₂

For operations that do not require high-purity cylinder oxygen.


FAQ

What people ask us before deciding

Why can't a PSA oxygen generator exceed 95 %?

Because zeolite retains nitrogen but does not tell argon from oxygen. Air contains 20.9 % O₂ and 0.9 % argon, and both leave together as product. Even if all the nitrogen were removed, the theoretical limit would be 95.7 % O₂.

Higher purities (99.5 % and above) require liquid oxygen or a second argon-separation stage.

How much compressed air does an oxygen generator use?

Between 10 and 12 Nm³ of air at 7 bar(g) per Nm³ of O₂, depending on purity. That is far more than a nitrogen generator, because oxygen is only a fifth of the air and almost all the rest has to be retained.

That is why the compressor and its efficiency set the cost per Nm³ of oxygen, and we size it together with the generator.

Are they suitable for medical use?

Oxygen for human use is a medicinal product, and its on-site production is subject to specific health regulations. The equipment in this range is offered for industrial use. If your project is medical, ask us and we will point you in the right direction.

What maintenance do they need?

Air-line maintenance (filters, dryer and drains), inspection of the cycle valves and calibration of the oxygen analyser. With dry, oil-free air, zeolite keeps its capacity for many years.

What harms it most is moisture: if the dryer fails, water takes the active sites of the zeolite and purity falls.

PSA generator or liquid oxygen?

For continuous consumption at 90–95 % purity, a PSA generator usually offers a much lower cost per Nm³ and removes tank rental, deliveries and boil-off losses. Liquid oxygen makes sense for high purities or very occasional consumption.

Many plants combine both: the generator covers the base load and liquid oxygen stays as back-up.

Why don't you publish prices?

Because the real cost depends on the complete plant: compressor, drying, filtration, receivers and installation. After the study we give you a firm quotation and the cost of your Nm³ of oxygen.

What would your own oxygen cost?

Tell us your consumption, the purity you need and how you buy oxygen today. We come back with the model, the compressor and the cost per Nm³.

WhatsApp